I got my other interface up and recognized in squeak but only the ipv4 address, not its ipv6 address. I tried adding the ipv6 address to the hosts file but it still did not work. Are others getting the inet6 addresses? Obviously, I am oblivious that it is my machine config, but I am unsure how to config it right.
Here are my results with 'callistohouse' configured. I stuck.
(NetNameResolver addressesForName: NetNameResolver localHostName) select: [ :each | each addressFamilyName == #inet6 ] thenCollect: [ :each | each socketAddress hostNumber ]. an OrderedCollection()
NetNameResolver addressesForName: NetNameResolver localHostName an OrderedCollection(192.168.43.32(callistohouse),0(0)-inet4-stream-tcp)
wlp2s0 Link encap:Ethernet HWaddr 40:25:c2:b0:7b:0c inet addr:192.168.43.32 Bcast:192.168.43.255 Mask:255.255.255.0 inet6 addr: fe80::94ac:2d16:6700:1ed5/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:101 errors:0 dropped:0 overruns:0 frame:0 TX packets:152 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:98104 (98.1 KB) TX bytes:18112 (18.1 KB)
NetNameResolver useOldNetwork. "true" false NetNameResolver hasIpv6PrimSupport. "true" true NetNameResolver enableIPv6. true NetNameResolver enableIPv6: true. NetNameResolver NetNameResolver useOldNetwork. " false" false NetNameResolver localHostAddress. 192.168.43.32(callistohouse),0(0) NetNameResolver localHostName. 'callisto' NetNameResolver addressForName: 'localhost'. "::1(localhost),0(0)" 127.0.0.1(localhost),0(0) NetNameResolver addressForName: 'callisto'. "::1(localhost),0(0)" 192.168.43.32(callistohouse),0(0) NetNameResolver addressForName: 'callistohouse'. "::1(localhost),0(0)" 192.168.43.32(callistohouse),0(0)
On 09/23/2017 09:32 AM, Levente Uzonyi wrote:
On Sat, 23 Sep 2017, Alan Pinch wrote:
Hi Tobias,
Running ifconfig on my Ubuntu box shows an ethernet inteface, my wireless uplink. This inteface does not show up in addressesForName:, whether I call it with 'callisto' or 'localhost'. Your call to the
The primitive shows what the DNS service on your machine provides. If there is no name attached to your IPv6 address, it won't show up (unless you know its address, because you can use that too).
AFAIK, the VM can't tell what interfaces are avaiable, which is probably what you're actually looking for.
Levente
ipv6-test.com site works. Is it possible that last works, as the machine is ipv6 enabled, but squeak primitive is still missing that interface for some reason. I know you cannot know my machine's configuration to debug. Perhaps you could tell me how to debug here for you? I am not sure of the next step and I question my wherewithall.
At your service, Alan
wlp2s0 Link encap:Ethernet HWaddr 40:25:c2:b0:7b:0c inet addr:192.168.43.32 Bcast:192.168.43.255 Mask:255.255.255.0 inet6 addr: fe80::94ac:2d16:6700:1ed5/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:97074 errors:0 dropped:0 overruns:0 frame:0 TX packets:52659 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:106056900 (106.0 MB) TX bytes:9058187 (9.0 MB)
NetNameResolver localHostName 'callisto' NetNameResolver addressesForName: NetNameResolver localHostName an OrderedCollection(127.0.1.1(callisto),0(0)-inet4-stream-tcp)
NetNameResolver addressesForName: 'localhost' an OrderedCollection(127.0.0.1(localhost),0(0)-inet4-stream-tcp)
On 09/18/2017 10:46 AM, Tobias Pape wrote:
Hi Alan
On 18.09.2017, at 10:19, Alan Pinch alan.c.pinch@gmail.com wrote:
I am running the Ubuntu 32-bit vm and I enabledIPv6: through the
preferences browser. I am able to run yet it seems it is still IPv4. I do not know enough how IPv6 should work. I get the following host addresses:
Connection
running..<cap://127.0.1.1:10012/Xrlgak8yDT0hgspNx0AyWoCdoZo=, cap://127.0.0.1:47684/FL4dilz6eq2sZDG5wKp3TFDoQEE=>
I get the following from NetNameResolver localAddressString 127.0.1.1
I just checked. Bear with me here:
In most imaged you will see for
printIt NetNameResolver useOldNetwork. "true"
If your VM and OS supports IPv6 (it should) you will see
printIt NetNameResolver hasIpv6PrimSupport. "true"
So you then can
doIt NetNameResolver enableIPv6: true.
If that worked, you will find
printIt NetNameResolver useOldNetwork. " false"
From now on, you will get more "interesting" network names. Look at the
result of
NetNameResolver localHostAddress. NetNameResolver localHostName.
(note that those are typically NOT localhost) Also you should see
printIt NetNameResolver addressForName: 'localhost'.
"::1(localhost),0(0)"
-=-=-=-=-=-=-
So far so good.
If you now try to, for example get some IPv6-enabled url, your should see
printIt (WebClient httpGet: 'http://ipv6-test.com') status. "
'HTTP/1.1 200 OK'"
But this won't probably work _unless_ you have the fixes in your image
which I uploaded just 5 minutes ago (WebClient-topa.110, Network-topa.205) ;)
Best regards -Tobias
Alan
On 09/17/2017 10:44 PM, David T. Lewis wrote:
On Sun, Sep 17, 2017 at 09:46:49PM -0400, Alan Pinch wrote:
Could anyone be able to point me to working IPv6 code for squeak, please? I would appreciate any link.
Alan
In the preferences browser, catagory general, set the preference for "Enable IPv6 and new network support" to true.
The default setting is false, largely because of some network name resolver issues on the Windows platform.
I do not think that the IPv6 code is exercised much, because most people probably leave their image in the default mode. So if you are using this and find problems with it, please let us know what does not work.
Dave
-- Thank you for your consideration, Alan